[FIRMWARE] 4.0.18.9926 for UAP/USW has been released | Stable Candidate

[UniFi]

We've prepared firmware 4.0.18.9926. Please see below for the changelog and links to the firmware binaries.


Firmware changes since 4.0.15:

• [UAPG2] Fix an issue causing latency in high traffic installations.
• [UAPG1] Switch to LEDE framework.* IMPORTANT NOTICE BELOW
• [HD/SHD/XG/BaseStationXG] Improve stability.
• [HD/SHD/XG/BaseStationXG] Optimize multicast traffic.
• [nanoHD/IW-HD] Fix DTIM provisioning issue.
• [nanoHD/IW-HD] Fix a bug in TX power provisioning.
• [nanoHD/IW-HD] Fix WiFi Experience feature (reported HERE).
• [nanoHD/IW-HD] Fix bandsteering disconnection issue.
• [nanoHD/IW-HD] Fix wireless uplink bandwidth mismatch issue.
• [nanoHD/IW-HD] Fix displayed RX rate issue (reported HERE).
• [nanoHD/IW-HD] Fix available channel list for China.
• [nanoHD/IW-HD] Fix fast-apply issue with changing channel width.
• [IW] Fix status LED.
• [UAP] Improve wireless uplink loop detection feature.
• [UAP] Fix a bug that may cause MAC ACL and bandsteering to conflict in certain configurations.
• [UAP] Fix uplink detection function.
• [UAP] Fix ifindex reporting via SNMP.
• [UAP] Properly isolate dynamic VLANs.
• [UAP] Security improvement for guest authentication.**
• [USW] Fix various bugs causing WiFi clients to show as wired once disconnected from WiFi network (reported HERE).
• [HW] Miscellaneous bug fixes and improvements.

*All supported 1st gen APs need to be on a minimum of 4.0.10 prior to upgrading to this firmware. Controller 5.10.3+ will force an upgrade to 4.0.10 prior to upgrading to this release (only if your device isn't running 4.0.10 already).



**Controller support pending.



NOTES:

• You may start to see EVT_AP_RestartProc events in the controller log. If you see these, please report if there is anything specifically in your setup that triggers the events. The processes restarting is not new, but the reporting of the restarting is, and we are using these reports to clean up these issues.
• Any US-XG-6POE upgrading from 4.0.2 or earlier will take a long time to upgrade. Don't be surprised if your switch is unavailable for 5-10+ minutes as 4.0.3+ also updates the PoE firmware to improve PD compatibility.
• 1st gen UAPs may require extra steps when upgrading from firmware 4.0.3. You can try disabling all WLAN groups, and then running the upgrade. Devices that are seemingly "stuck" on 4.0.3 may require TFTP recovery to upgrade from that firmware.
• All supported 1st gen APs need to be on a minimum of 4.0.10 prior to upgrading to this firmware. Controller 5.10.3+ will force an upgrade to 4.0.10 prior to upgrading to this release (only if your device isn't running 4.0.10 already).

Download:

• UAP-AC-Lite/LR/Pro/EDU/M/M-PRO/IW/IW-Pro | binary | md5sum | sha256sum
• UAP-HD/SHD/XG/BaseStationXG | binary | md5sum | sha256sum
• UAP-nanoHD/IW-HD | binary | md5sum | sha256sum
• UAP, UAP-LR, UAP-OD, UAP-OD5 | binary | md5sum | sha256sum
• UAP-v2, UAP-LR-v2 | binary | md5sum | sha256sum
• UAP-IW | binary | md5sum | sha256sum
• UAP-Pro | binary | md5sum | sha256sum
• UAP-OD+ | binary | md5sum | sha256sum
• USW | binary | md5sum | sha256sum
• US-L2-POE | binary | md5sum | sha256sum
• US-16-XG | binary | md5sum | sha256sum
• US-XG-6POE | binary | md5sum | sha256sum
• USW-Multi | binary | md5sum | sha256sum*

*This firmware is meant to be a one file solution that works with all models of UniFi switch. You can use it when upgrading from 3.9.40+ only. It will not work when upgrading from earlier releases.



Any and all feedback is welcome, including lettings us know about successful device upgrades. When reporting an issue, please ensure that you include the following information:

1. Controller version.
2. Firmware version (previous and current).
3. Device model(s).

Links are all HTTPS. This assumes your device(s) are currently running at least 3.7.51, and that the device's date is properly set (i.e. it can reach a NTP server). If you encounter issues with the upgrade, or your device isn't on a minimum supported firmware, then you can change the link to HTTP before performing the upgrade.


Verder lezen...

 

[Weidbeens]

Nog geen problemen gevonden.
De problemen uit versie 4.0.17 lijken nu opgelost.

 

[PE1PQX]

Vreemd, ik krijg deze update niet in mijn spulletjes...

 

[Hofstede]

Dit is een Stable Candidate, dat betekent dat deze firmware nog niet naar de controller wordt gepushed. Dat gebeurt meestal pas een aantal dagen nadat de status is gewijzigd in Stable. Tenzij er nog fouten worden gevonden in deze Stable Candidate, dan komt er weer een 4.0.19 Stable Candidate etc., etc.
Wil je hem proberen moet je hem via een Custom upgrade installeren.

 

[Weidbeens]

Op dit moment zijn er toch nog teveel problemen met deze Beta.
UBNT is momenteel keihard bezig naar verbeteringen te zoeken en zal zsm een volgende Beta lanceren.
Om in het Beta programma mee te doen, moet je hiervoor speciaal zijn aangemeld.

 

[Hofstede]

Deze firmware is al geen beta meer maar Stable Candidate. Dus je hoeft er geen beta access voor te hebben.

 

[PcRene]

Ik ben van de 4.18 toch weer terug naar de 4.15
Download bij 4.18 : 90Mb
4.15: 200Mb

Rene