[FIRMWARE] 3.9.54.9373 for UAP/USW has been released | Stable Candidate

[UniFi]

We've prepared firmware 3.9.54.9373. Please see below for the changelog and links to the firmware binaries. This is initially being released as stable candidate, which means it will only be available via this blog post. It may move to stable status after some time.

Firmware changes since 3.9.50:

• [UAPG3] Fix IP endianness issue affecting reported `Framed-IP-Address` in RADIUS accounting.
• [UAPG2/G3] Add advanced guest isolation support.*
• [UAPG2/G3] Fix a leak which may cause provisioning/upgrade issues (`Timeout waiting for OL vap X to stop` in syslog).
• [nanoHD/IW-HD] Add support for minimum PHY rate control.
• [nanoHD/IW-HD] Improve stability.
• [nanoHD/IW-HD] Improve throughput with high client STA count.
• [nanoHD/IW-HD] Enhance bandsteering and set daemon to 802.11v BSS Transition Management (BTM) only mode.
• [nanoHD/IW-HD] Fix client STA can't connect after WLAN schedule executed (reported HERE).
• [nanoHD/IW-HD] Fix bug which would cause default SSIDs to broadcast in some cases.
• [IW-HD] Add wired 802.1X support.*
• [IW-HD] Fix an issue with client STA roaming.
• [IW-HD] Fix scheduling while atomic bug which caused the management daemon to crash (reported HERE).
• [UAP] Add loop detection to wireless uplink.
• [UAP] Fix a bug in RADIUS MAC Auth provisioning.
• [USW] Fix LAG port LED off issue.
• [HW] Miscellaneous bug fixes and improvements.

*Controller support pending.

NOTE: You may start to see EVT_AP_RestartProc events in the controller log. If you see these, please report if there is anything specifically in your setup that triggers the events. The processes restarting is not new, but the reporting of the restarting is, and we are using these reports to clean up these issues.

IMPORTANT NOTE: In preparation for an upcoming code merge, we've updated the minimum firmware version to 3.9.42 for certain hardware. That means if you flash this firmware onto any HD/SHD/XG/BaseStationXG then you will not be able to downgrade to firmware prior to 3.9.42.

Download:

• UAP-AC-Lite/LR/Pro/EDU/M/M-PRO/IW/IW-Pro | binary | md5sum | sha256sum
• UAP-HD/SHD/XG/BaseStationXG | binary | md5sum | sha256sum ****See important note above****
• UAP-nanoHD/IW-HD | binary | md5sum | sha256sum
• UAP, UAP-LR, UAP-OD, UAP-OD5 | binary | md5sum | sha256sum
• UAP-v2, UAP-LR-v2 | binary | md5sum | sha256sum
• UAP-IW | binary | md5sum | sha256sum
• UAP-Pro | binary | md5sum | sha256sum
• UAP-OD+ | binary | md5sum | sha256sum
• USW | binary | md5sum | sha256sum
• US-L2-POE | binary | md5sum | sha256sum
• US-16-XG | binary | md5sum | sha256sum
• USW-Multi | binary | md5sum | sha256sum*

*This firmware is meant to be a one file solution that works with all models of UniFi switch. You can use it when upgrading from 3.9.40+ only. It will not work when upgrading from earlier releases.

Any and all feedback is welcome, including lettings us know about successful device upgrades. When reporting an issue, please ensure that you include the following information:

1. Controller version.
2. Firmware version (previous and current).
3. Device model(s).

Links are all HTTPS. This assumes your device(s) are currently running at least 3.7.51, and that the device's date is properly set (i.e. it can reach a NTP server). If you encounter issues with the upgrade, or your device isn't on a minimum supported firmware, then you can change the link to HTTP before performing the upgrade.


Verder lezen...

 

[Springer]

Iemand deze al draaien? Heb het gevoel dat bij deze firmware de roaming niet zo goed werkt, mijn mobiele devices maken nu contact met AP-Pro in de meterkast ipv de dichtbij zijnde woonkamer. Na mijn weten had ik dat niet met de vorige firmware.