Update voor Unifi (4.0.14.9736)

PE1PQX

Brons
UniFier
27 okt 2018
1.380
774
163
49
Land van Bartje
www.pe1pqx.eu
Ik zag in de Cloud-Key web-pagina dat er een update klaar staat naar 4.0.14.9736.
Update tijd dus.


We've prepared firmware 4.0.14.9736. Please see below for the changelog and links to the firmware binaries.

Firmware changes since 4.0.10:
  • [HD/SHD/XG/BaseStationXG] Fix handling of IEs so wildcard SSIDs don't cause memory corruption.
  • [HD/SHD/XG/BaseStationXG] Resolve an illegal memory access when bonding enabled.
  • [XG/BaseStationXG] Enable multi-radio wireless uplink.
  • [HD/SHD] Enable VHT160 support.*
  • [nanoHD/IW-HD] Fix downlink stays disconnected after channel change or reboot when uplink using DFS channels (reported HERE).
  • [nanoHD/IW-HD] Fix ADDBA Request loop triggered by some client STAs (reported HERE).
  • [nanoHD/IW-HD] Fix dynamic VLAN with Fast Roaming issue.
  • [UAPG2] Fix physical reset function.
  • [UAP] Fix channel 14 support.
  • [UAP] Fix issue where all downlink APs are disassociated when one downlink detects a network loop.
  • [USW] Add alert temperature to environment stats.
  • [HW] Fix an adoption issue which may occur after a known device is reset to factory defaults.
  • [HW] Miscellaneous bug fixes and improvements.
*VHT160 RF scanning on HD/SHD is not supported.

NOTE: You may start to see EVT_AP_RestartProc events in the controller log. If you see these, please report if there is anything specifically in your setup that triggers the events. The processes restarting is not new, but the reporting of the restarting is, and we are using these reports to clean up these issues.

SPECIAL NOTES:
  • Any US-XG-6POE upgrading from 4.0.2 or earlier will take a long time to upgrade. Don't be surprised if your switch is unavailable for 5-10+ minutes as 4.0.3+ also updates the PoE firmware to improve PD compatibility.
  • 1st gen UAPs may require extra steps when upgrading from firmware 4.0.3. You can try disabling all WLAN groups, and then running the upgrade. Devices that are seemingly "stuck" on 4.0.3 may require TFTP recovery to upgrade from that firmware.

Download:
*This firmware is meant to be a one file solution that works with all models of UniFi switch. You can use it when upgrading from 3.9.40+ only. It will not work when upgrading from earlier releases.

Any and all feedback is welcome, including lettings us know about successful device upgrades. When reporting an issue, please ensure that you include the following information:
  1. Controller version.
  2. Firmware version (previous and current).
  3. Device model(s).
Links are all HTTPS. This assumes your device(s) are currently running at least 3.7.51, and that the device's date is properly set (i.e. it can reach a NTP server). If you encounter issues with the upgrade, or your device isn't on a minimum supported firmware, then you can change the link to HTTP before performing the upgrade.

(Bron: https://community.ubnt.com/t5/UniFi...UAP-USW-has-been-released-Stable/ba-p/2610088 )

PS.: als dit bericht verkeerd staat, dan excuus...
 
  • Leuk
Waarderingen: mchp92
Deze meldingen worden op dit forum automatisch gepost in het Unifi Updates Blog.
 
Activiteit
Er wordt op dit moment (nog) geen nieuwe reactie gepost.
  Topic Status: Hallo . Er is al meer dan 14 dagen geen nieuwe reactie meer geplaatst.
  De inhoud is mogelijk niet langer relevant.
  Misschien is het beter om in plaats daarvan een nieuw onderwerp te starten..