Official UniFi Network Controller 6.1.65

[Hempie]

Overview​

* MacOS version is not available for this release.
* This release is an Release Candidate.

Improvements​

• Add alert for Client roaming from AP to another AP.
• Add "Clear Filter" buttons when no content is displayed in Client and Device section.
• Improve Client Page performance.
• Preserve Uplink between controller restarts or when device becomes disconnected.
• Display device waiting for adoption without page reload.
• Block disconnect/reconnect alerts if device is upgrading firmware.
• Update metric suffixes used in Devices and Clients page.

Bugfixes​

• Fix legacy WLAN Schedules migration when it is disabled.
• Fix UDM shows as disconnected due to configuration error.
• Fix devices on WAN2 appearing in clients list.
• Fix missing WAN failover property on UXG.
• Fix device shown as disconnected during adoption.
• Fix Topology label sizes in Safari.
• Fix device icon in property panel for APs.
• Fix Device model name in WiFiman table and property panel topology.
• Fix property panel for disconnected devices.
• Fix Site Switcher, switch Site without page reload, save last used Site.
• Fix broken tooltips for Wireless Experience Score charts.
• Fix AP group creation for Non-UniFi OS controllers.
• Fix broken Device, Clients and Alerts page filter.
• Fix Client fingerprint and displayed data in 24HR usage column.
• Fix IPS dashboard map not loading.
• Fix UDM Base property panel device tab.
• Fix Topology node positioning for larger setups.
• Fix WPA3 Enhanced/192 remaining enabled after changing network security type.
• Fix configuration error when missing server certificate for WiFiman.
• Fix reporting performance issues for wired clients.
• Prevent UDM WAN port edit as LAN port.
• Allow configuring port interfaces in gateway device property panel.
• Remove Safari rendering artefacts in topology while panning/zooming.
• Remove migrated disabled WLAN schedule entries (only for unmodified WiFi settings since 6.1.61).
• Add SFP+ ports to VLAN Only networks.

Additional information​

Please report any issues you encounter with this release using the Report Bug form.
(Recommended) - Create an up-to-date backup before upgrading your controller in the event any issues are encountered.

• Existing UniFi Network controllers must be on one of the following versions in order to upgrade directly to this version:

Info

6.1.65 and earlier 6.1.x versions.
6.0.45 and earlier 6.0.x versions.
5.14.25 and earlier 5.14.x versions.
5.13.33 and earlier 5.13.x versions.
5.12.72 and earlier 5.12.x versions.
5.11.52 and earlier 5.11.x versions.
5.10.27 and earlier 5.10.x versions.
5.9.33 and earlier 5.9.x versions.
5.8.30 and earlier 5.8.x versions.
5.7.28 and earlier 5.7.x versions.
5.6.42 and earlier 5.6.x versions.
Most earlier versions are also supported for direct upgrade, going back to 3.1.0.

• Controller updates may cause your adopted devices to reprovision after controller upgrades.
• An updated/current version of Java 8 must be installed on the system hosting the controller software. Java 9 and later are not yet supported.
• As of UniFi Network controller 5.9, if using Cloud Access, the host system/device requires outbound 8883/tcp to be open/unrestricted. Find up-to-date port requirements here.
• Minimum supported device firmware for U6-Series devices is 5.29.0, UAP/USW is 4.0.9, and for USG it's 4.4.34.
• If you have any 'service dns forwarding options' configuration defined in config.gateway.json, it will overwrite the provisioning of statically defined name servers, leaving you with no DNS. Either remove the 'service dns forwarding options' portion of config.gateway.json, or add additional 'options' lines defining name servers, such as 'server=1.1.1.1', 'server=8.8.8.8', etc.

Microsoft Windows specific

• Users running 64-bit Windows should only have 64-bit Java installed. If you have 32-bit Java installed then we recommend uninstalling it.

macOS Specific

• We stopped bundling Java as of UniFi Network 5.11.47. If you're installing that release or later please make sure you have manually installed a current release of Java 8 beforehand. Only the Java Runtime Environment (JRE) is required.
• Oracle JRE 8 offers the simplest path as it will simply "just work" without requiring any changes. We may investigate alternative JVMs and update this message accordingly.

Debian/Ubuntu specific

• For Debian/Ubuntu users installing via our repo, please update your APT source (see HERE).
• We support MongoDB 3.6 since 5.13.10, older controllers only support up to MongoDB 3.4.

Checksums

Info

f264ea2aae61bb11831ad48d24139c21 *UniFi-installer.exe
96cb20aa5359e7dd70cfc92cb0ae559b *unifi_sysvinit_all.deb
601df32736f41e40a80a3e472450a3e1 *unifi_sh_api


------------------------------------------------------------------------------------------------------------------------


SHA256(UniFi-installer.exe)= 70225e9c1059d9689ba69e803e0c48cfcc9c9c930242e803d45378cd9c3e2d51
SHA256(unifi_sysvinit_all.deb)= 180d5a72b713cc4fd9b80bb429b88ff177877558a1ee55d0355682ab63c6e6aa
SHA256(unifi_sh_api)= 1791685039ea795970bcc7a61eec854058e3e6fc13c52770e31e20f3beb622eb

Download links
UniFi Controller for Windows
UniFi Controller for Debian/Ubuntu and UniFi Cloud Key
unifi_sh_api (shell library)